Reset service light indicator BMW 3 Series

Reset service light indicator BMW 3 Series. For models: BMW E21, BMW E36, BMW E46, BMW E90, BMW E91, BMW E92, BMW E93, BMW F30, BMW F31.

Reset service light indicator BMW 3 Series. For model: BMW E36. From years: 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000.

How to reset service light indicator BMW 3 Series model E36.

1. Let’s go on with the search. The diagnostic connector (the black cylinder in the figure). Is located in the engine compartment, near the brake fluid box.  Picture below.
2. .
3. You have to remove the cap on top and you’ll see a 20 pin connector like this.
4. Our interest is to use the pins 7 and 19 (red marked in the figure), necessary to reset service light indicator BMW 3 Series modelignitio E36. Picture below.
5. .

The procedure how do you reset service light indicator BMW 3 Series model E36.

1. First, make sure that the ignition switch is in position 0 (that means no operating of any kind).
2. Remove the key.
3. Then place a jumper wire (refer to the end of this file) between the pins 7 and 19. Picture below.
4. .

Inspection: reset service light indicator BMW 3 Series model E36.

1. When you see INSPECTION light in the instrument cluster. IT’s time to perform an inspection reset.
2. The reset procedure is the same as above, axceot for the time to maintain the connection. In this case you should remove the jumper wire after approx 12 seconds.
3. The INSPECTION light disappearsand the green lights come out.
4. Turn off, replace the cap, close.

Reset service light indicator BMW 3 Series. For model: BMW E90. From years: 2005, 2006, 2007, 2008, 2009, 2010, 2011.

How do you reset service light indicator BMW 3 Series model E90.

1. Insert your remote key into the key slot and press the START button once without putting your foot on the brake. You should see numerous lights turn on in the dash.
2. Wait for any warning lights and beeping to go off. Picture below.
3. .
4. Then you hold the brake. Press and hold the odometer button, which is located on the bottom left of the speedometer (instrument cluster). Picture below.
5. .
6. An exclamation mark will appear in the screen in middle of the dashboard. Picture below.
7. .
8. Keep holding down the button until the next picture appears then let go. Picture below.
9. .
10. When you arrive at the inspection service light that you wish to reset press and hold the BC button on the signal handel until the text Reset is visible under the picture, then let go.
11. The service light, below figure. Picture below.
12. .

Reset service light indicator BMW 3 Series model E91. From years: 2005, 2006, 2007, 2008, 2009, 2010, 2011.

How do you reset service light indicator BMW 3 Series model E91.

1. Insert key.
2. Press START/STOP button without pressing clutch/brake, wait for the service reminder to disappear.
3. Immediately, after service reminder goes out, press and hold the odometer reset. After 3 seconds a warning triangle will appear. Picture below.
4. .
5. Keep the odometer reset button pressed. After another 2-3 seconds the oil-can symbol will appear. If you hold the button too long, about 10 seconds, the system will go into an internal coding mode. In this case, shut everything down and start over.
6. After properly performing step-3, the system will be in the service menu mode. Use the push button (BC button) on the end of the left steering column switch (wipers, high/low beams) to scroll through the various service items.
7. When the service light indicator that you wish to reset is displayed, press the BC button on the end of wiper switch. “Reset” should now appear in the display. Press and hold the BC button for 2-3 seconds. A small clock display will show as the reset is being performed.
8. Reset service light indicator BMW 3 Series E91, picture below.
9. .
10. You can now select another item to reset (as in step-4) or press the START/STOP button to end.

 

Reset service light indicator BMW 3 Series model E92. From years: 2005, 2006, 2007, 2008, 2009, 2010, 2011.

How do you reset service light indicator BMW 3 Series model E92.

1. Insert key.
2. Press START/STOP button without pressing clutch/brake, wait for the service reminder to disappear.
3. Immediately, after service reminder goes out, press and hold the odometer reset. After 3 seconds a warning triangle will appear. Picture below.
4. .
5. Keep the odometer reset button pressed. After another 2-3 seconds the oil-can symbol will appear. If you hold the button too long, about 10 seconds, the system will go into an internal coding mode. In this case, shut everything down and start over.
6. After properly performing step-3, the system will be in the service menu mode. Use the push button (BC button) on the end of the left steering column switch (wipers, high/low beams) to scroll through the various service items.
7. When the service light indicator is displayed, press the BC button on the end of wiper switch. “Reset” should now appear in the display. Press and hold the BC button for 2-3 seconds. A small clock display will show as the reset is being performed.
8. Reset service light indicator BMW 3 Series model E92, picture below.
9. .
10. You can now select another item to reset (as in step-4) or press the START/STOP button to end.

 

Reset service light indicator BMW 3 Series model E93. From years: 2005, 2006, 2007, 2008, 2009, 2010, 2011.

1. Insert key.
2. Press START/STOP button without pressing clutch/brake, wait for the service reminder to disappear.
3. Immediately, after service reminder goes out, press and hold the odometer reset. After 3 seconds a warning triangle will appear.
4. .
5. Keep the odometer reset button pressed. After another 2-3 seconds the oil-can symbol will appear. If you hold the button too long, about 10 seconds, the system will go into an internal coding mode. In this case, shut everything down and start over.
6. After properly performing step-3, the system will be in the service menu mode. Use the push button (BC button) on the end of the left steering column switch (wipers, high/low beams) to scroll through the various service items.
7. When the service light indicator is displayed, press the BC button on the end of wiper switch. “Reset” should now appear in the display. Press and hold the BC button for 2-3 seconds. A small clock display will show as the reset is being performed.
8. Reset service light indicator BMW 3 Series E93, picture below.
9. .
10. You can now select another item to reset (as in step-4) or press the START/STOP button to end.

 

That it is the full procedure how to reset service light indicator BMW 3 Series model E93. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for BMW cars. Or any error which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders when by yourself.

 This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Click hear to see full procedure how do you reset the oil light indicator. How to reset the maintenance light and how do you reset service light for all BMW cars.