Do it yourself, change the hood support struts on your Volvo XC90, the model made between the years 2003 and 2013. The replacement process for these parts is very, very simple and it will require only a flat blade screwdriver. We recommend you though, to use the help of another person when you remove the …
How to change the hood support struts on Volvo XC90 2003-2013 Read More »
Do it yourself, change the side marker light assembly on your Volvo XC90. The repair process is for models manufactured between the years 2003 and 2013. You will only need a flat headed screwdriver and a couple of minutes to do the replacement. In the beginning, you will have to go in front of …
DIY, change the side marker light on Volvo XC90 2003-2013 Read More »
How to replace the coolant recovery tank on your Volvo XC90, the model produced between the years 2003 and 2013. You will only require a flat blade screwdriver and probably less than 20 minutes, because the process is quite simple. You can start after you open and secure the hood of the car. Go above …
How to replace the coolant recovery tank on Volvo XC90 2003-2013 Read More »
Do it yourself, change the fog lights on your Subaru Outback, the model produced between the years 2000 and 2004. This replacement requires a 10 mm socket wrench and a flat blade screwdriver. You might consider using a jack stand to make the process easier. With all the tools needed, you should complete the task …
DIY, change the fog lights on Subaru Outback 2000-2004 Read More »
DIY, change the tail light assembly on your Subaru Outback, the model produced between the years 2000 and 2004. This replacement is quite simple and it will only require a flat blade screwdriver and an 8 mm socket with a ratchet and extension. The whole process will probably not take you more than half an …
How to change the tail light on Subaru Outback 2000-2004 Read More »
DIY, change the headlight assembly on your Volvo XC90, manufactured between the years 2003 and 2013. You will not require tools to make this replacement and the process is very simple. Only if you need to service the main light bulbs, you will need a Phillips screwdriver, because one of them has a plastic cover that is …
How to change the headlight assembly on Volvo XC90 2003-2013 Read More »
Do it yourself, change the ignition coils on your Volvo XC90. You will require T25 and T30 torx bit drivers and a 10 mm socket. The replacement is not that difficult, but it will most probably take you more than half an hour. The ignition coils on this car are located beneath the plastic engine …
DIY, remove and change the fog lights on your Volvo XC90, the model made between 2003 and 2013. You will need A T25 torx driver with a ratchet and extensions to make this replacement. The process is not that difficult, but it might take you more than half an hour. We recommend you …
DIY, change the fog lights on Volvo XC90 2003-2013 Read More »
Do it yourself, remove the rear door panel on your Subaru Outback, the model made in the years 2000, 2001, 2002, 2003 and 2004. This procedure will require a flat blade screwdriver and a Phillips screwdriver. Removing the rear door panel on this car isn’t a difficult process, so you will be able to do it …
How to remove the rear door panel on Subaru Outback 2000-2004 Read More »
Do it yourself, change the master window switch on your Subaru Outback. The repair process shown below is similar for Outback models produced in the years 2000, 2001, 2002, 2003 and 2004. This is a very simple replacement that can be done in no more than 15 minutes. You will only require a flat blade screwdriver …
How to change the master window switch on Subaru Outback 2000-2004 Read More »
