Reset tire pressure warning light Toyota FJ Cruiser

Reset tire pressure warning light Toyota FJ Cruiser. From year: 2012, 2013, 2014.

How to reset tire pressure warning light Toyota FJ Cruiser.

How to initialize the tire pressure warning system.

  1. Park the vehicle in safe place and turn the engine switch to the LOCK position. While the vehicle is moving, initialization is not performed.
  2. Adjust the tire inflation pressure to the specified cold tire inflation pressure level. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the engine switch to the ON position.
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.
  5. Reset tire pressure warning system Toyota FJ Cruiser
  6. Wait for a few minutes with the engine switch on, and then turn the engine switch to the ACC or LOCK position.

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.

When to replace your Toyota FJ Cruiser tires.

Tires should be replaced if:

  • You have tire damage such as cuts, splits, cracks deep enough to expose the fabric or bulges indicating internal damage.
  • A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage.

If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels on your Toyota FJ Cruiser.

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.

Tire life.

Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.

If the tread wears down below 0.16 in. (4 mm) on snow tires.

The effectiveness of snow tires is lost.

Toyota FJ Cruiser maximum load of tire.

Check that the number given by dividing the maximum load by 1.10 of the replacement tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. For the GAWR, see the Certification Label. For the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire.

Toyota FJ Cruiser maximum load of tire.

Initializing the tire pressure warning system.

Initialize the tire pressure warning system with the tire inflation pressure adjusted to the specified level.

If you press the tire pressure warning reset switch accidentally.

If initialization is performed, adjust the tire inflation pressure to the specified level and initialize the tire pressure warning system again.

When the initialization of the tire pressure warning system has failed.

Initialization can be completed in a few minutes. However, in the following cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer.

When operating the tire pressure warning reset switch, the tire pressure warning light does not blink 3 times.

After carrying out the initialization procedure, the tire pressure warning light blinks for 1 minute then stays on after driving for about 20 minutes.

Routine tire inflation pressure checks.

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

Tire pressure warning system certification.

FCC ID: PAXPMV107J

FCC ID: HYQ13BCX

When initializing the tire pressure warning system.

Do not press the tire pressure warning reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.

All information how to reset tire pressure warning light is taken from Toyota FJ Cruiser owners manual.

 

That it is the full procedure how to reset tire pressure warning light Toyota FJ Cruiser. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Click hear to see full procedure how do you reset the oil light indicator. How to reset the maintenance light and how do you reset service light for all Toyota vehicles.

Leave a Reply

Your email address will not be published. Required fields are marked *