Reset oil service light Mercury Mountaineer

Reset oil service light Mercury Mountaineer. From years: 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010.

How to reset oil service light Mercury Mountaineer. From years: 1999, 2000, 2001.

Oil change reset Mercury Mountaineer.
Press the OIL CHANGE RESET control to reset the oil life feature to 100% (or your personalized oil reset percentage) (at optimal driving conditions, 100% oil life is equivalent to a maximum of 12 000 kilometers [7 500 miles]). After you have the oil changed, you must press and hold the OIL CHANGE RESET control for five seconds. The message center will count down for five seconds. After a successful reset, the message center will display OIL LIFE RESET TO 100%. (If you have established a personalized oil reset percentage, the display will show that percentage instead of 100%.) This reset procedure should be performed only after an oil change to ensure accurate oil life indications. 

Your personalized oil reset percentage allows you to establish a smaller oil change interval than the manufacturer’s recommended interval. To establish your personalized oil reset percentage: 

  1. Turn the ignition to run, one position before starting engine.
  2. Press and hold the OIL CHANGE RESET control and press the RESET control while the display is still counting down the five seconds to reset. The display will change to START OIL LIFE AT XXX%. 
  3. Press the OIL CHANGE RESET control until the displayed percentage is the personalized oil reset percentage you desire. Your choices are 100%, 90%, 80%, 70%, 60%, 50%, 40% and 30%.
  4. Press the RESET control to complete the procedure. Pressing any control other than RESET or OIL CHANGE RESET will abort this procedure and will not establish your new personalized oil reset percentage. 

When your personalized oil reset percentage has been established, it will be used beginning with the completion of your next OIL CHANGE RESET procedure.

Reset oil service light Mercury Mountaineer manual 1999-2001.

The full procedure how to reset oil service light Mercury Mountaineer is taken owners manual.

 

How do you reset oil service light Mercury Mountaineer. From years: 2002, 2003.

To reset the oil monitoring system to 100% after each oil change on a Mercury Mountaineer [approximately 8,000 km (5,000 miles) or 180 days] perform the following:

  1. Turn the ignition to run, one position before starting engine.
  2. Press the SETUP control to access the System Check function.
  3. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”.
  4. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”.
  5. Press and hold the RESET control to display OIL LIFE SET TO 100%. Your oil life is now reset.

 

To reset the oil monitoring system Mercury Mountaineer to your personalized oil life %:

  1. Press the SETUP control to access the System Check function.
  2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”.
  3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”.
  4. Release the RESET control momentarily, then press RESET and SETUP controls at the same time to activate a service mode which will display OIL LIFE XX% RESET TO ALTER.
  5. Press RESET until you find your personalized OIL LIFE XX%.
  6. With your personalized OIL LIFE XX% displayed, press SETUP to continue the system check.

CHANGE OIL SOON and OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed.

An oil change is required whenever indicated by the message center.

Reset oil service light Mercury Mountaineer manual 2002-2003.

All information how to reset oil service light Mercury Mountaineer is taken owners manual.

 

Full procedure how to reset oil service light Mercury Mountaineer. From years: 2004, 2005.

To reset the oil monitoring system to 100% after each oil change  on a Mercury Mountaineer [approximately 5,000 miles (8,000 km) or 180 days] perform the following:

  1. Turn the ignition to run, one position before starting engine.
  2. Press and release the SETUP control to display “PRESS RESET AT OIL CHANGE”.
  3. Press and release the RESET control to display “HOLD RESET TO CONFIRM”.
  4. Press and hold the RESET control for 2 seconds and release. Oil life is set to 100% and “OIL LIFE SET TO 100%” is displayed.

After you have done steps 1 through 4, you can reset the oil monitoring system to your personalized oil life %:

  1. Press RESET and SETUP controls at the same time for 2 seconds, to activate a service mode which will display “OIL LIFE XX% RESET TO ALTER”.
  2. Press RESET to decrement oil life by 10% down to 30% and back to 100%.
  3. With your personalized OIL LIFE XX% displayed, press SETUP to continue the system check.

CHANGE OIL SOON and OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed.

Reset oil service light Mercury Mountaineer manual 2004-2005.

All info how to reset oil service light Mercury Mountaineer is taken owners manual.

 

How to reset oil service light Mercury Mountaineer. From years: 2006, 2007.

  1. Turn the ignition to run, one position before starting engine.
  2. Enter SYSTEM CHECK to display OIL XXX% OIL LIFE OK.
  3. Press RESET button to display HOLD RESET IF NEW OIL.
  4. Press and hold the RESET button for more than two seconds.
  5. Oil life is set to 100% and OIL CHANGE SET TO 100% is displayed.
  6. Turn the ignition off and then start the engine to verify the indicator has been reset.

 

How can you reset oil service light Mercury Mountaineer. From years: 2008, 2009, 2010.

Oil life Setup and Start Value Mercury Mountaineer.

To reset the oil monitoring system to 100% after each oil change on a Mercury Mountaineer [approximately 7,500 miles (12,000 km) or six months] perform the following:

  1. Turn the ignition to run, one position before starting engine.
  2. To reset the oil monitoring system to 100% after each oil change [approximately 7,500 miles (12,000 km) or six months] perform the following:
  3. Press RESET control to display “HOLD RESET IF NEW OIL”.
  4. Press and hold the RESET control for more than two seconds. Oil life is set to 100% and “OIL CHANGE SET TO 100%” is displayed.
  5. To change oil life 100% miles value from 7,500 miles (12,000 km) or six months to another value, proceed to step 6.
  6. Once “OIL LIFE SET TO XXX%” is displayed, release and press the RESET control switch to change the Oil Life Start Value. Each release and press will reduce the value by 10 percent.

Note: Oil Life Start Value of 100% equals 7,500 miles (12,000 km) or six months. For example, setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,800 km) and 120 days.

OIL LIFE CHANGE SOON. Displayed when the engine oil life
reaches 5% or less of the Oil Life Start Value.

OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 0%. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS.

Reset oil service light Mercury Mountaineer manual 2008-2010.

All information how to reset oil service light Mercury Mountaineer is taken owners manual.

 

That it is the full procedure how to reset oil service light Mercury Mountaineer. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Mercury cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders when by yourself.

 This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Click hear to see full procedure how do you reset the oil light indicator. How to reset the maintenance light and how do you reset service light for all Mercury vehicles.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>