Reset dynamic laser cruise control master warning light Toyota Sienna

Reset dynamic laser cruise control master warning light Toyota Sienna second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010.

How to reset dynamic laser cruise control master warning light Toyota Sienna 2 generation.

This light warns that there is a problem somewhere in the dynamic laser cruise control system. The light will come on when the engine switch is turned to “ON” and go off after a few seconds. When the light comes on, the alarm sounds and the warning code will appear on the display. At this time, dynamic laser cruise control is cancelled.

Dynamic laser cruise control allows you to drive at a selected cruising speed over about 45 km/h (28 mph) with your foot off the accelerator pedal, maintaining an appropriate vehicle−to−vehicle distance.

Do not rely excessively on dynamic laser cruise control in order to avoid serious injury or death, or to prevent accidents or to control the vehicle’s speed in emergency situations. Do not use cruise control except in appropriate road and traffic conditions. Always drive carefully and attentively. Before using dynamic laser cruise control, read and understand the following instructions.

TURNING THE SYSTEM ON AND OFF.

To turn the dynamic laser cruise control on, turn the “ON−OFF” button on. The “CRUISE” and “READY” indicator lights on the instrument panel will come on to indicate that the vehicle−to−vehicle distance control mode is operational. Pressing the “ON−OFF” button again turns the system off. When the system is turned off, cruising speed and vehicle−to−vehicle distance must be reset when the vehicle−to−vehicle distance control mode is turned on again.

When the engine switch is turned off, the system is also automatically turned off. To use dynamic laser cruise control again, press the “ON−OFF” button again to turn it on. When the engine switch is turned off, all the preset data is cleared. When you use the dynamic laser cruise control again, you need to reset the data.

To avoid accidentally engaging the cruise control, turn the system off when it is not in use. Make sure the “CRUISE” indicator light is off.

RESETTING TO A FASTER SPEED.

Push the lever up in the “+ RES” direction and hold it. The displayed speed will increase in increments of 5 mph (for the U.S.A.) or 5 km/h (for Canada). Release the lever when the desired speed is attained. The vehicle speed will gradually increase to the display speed. However, a faster way to reset is to accelerate the vehicle and then push the lever down in the “− SET” direction.

When the vehicle−to−vehicle distance control is on, your cruising speed is regulated in proportion to the speed of the vehicle ahead, so increasing the preset speed using the control lever does not accelerate the vehicle. However, if the vehicle ahead leaves the lane, your cruising speed will increase to the preset speed because the preset speed has been set higher using the control lever. Confirm the setting on the display.

RESETTING TO A SLOWER SPEED.

Push the lever down in the “− SET” direction and hold it. The displayed speed will decrease in increments of 5 mph (for the U.S.A.) or 5 km/h (for Canada). Release the lever when the desired speed is attained. The vehicle speed will gradually decrease to the display speed. However, a faster way to reset is to depress the brake pedal and then push the lever down in the “− SET” direction. If the control lever is released when the vehicle speed exceeds the upper limit of the preset speed traveling downhill while you are pushing the lever down, the system will memorize the upper limit of the preset speed as a preset speed. Even if you downshift from “D” to “4” in the vehicle−to−vehicle distance control mode, engine braking will not be enabled because this mode is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. If you use the brake pedal, cruise control is cancelled.

 

That it is the full procedure how to reset dynamic laser cruise control master warning light Toyota Sienna second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Click hear to see full procedure how do you reset the oil light indicator. How to reset the maintenance light and how do you reset service light for all Toyota vehicles.

Leave a Reply

Your email address will not be published. Required fields are marked *